staging.inyokaproject.org

Alte Backups löschen

Status: Ungelöst | Ubuntu-Version: Xubuntu 17.10 (Artful Aardvark)
Antworten |

kirinoko

Anmeldungsdatum:
15. September 2015

Beiträge: 187

Hallo Linuxianer,

ich möchte euch um einen Tipp bitten, wie ich ein alte/unvollständiges Backup auf einer externen Festplatte löschen kann.

Mit dem Kontextmenü gibt es die gleiche Fehlermeldung, wie beim manuellen Löschversuch.

Manuell sieht es so aus - ob das richtig ist? (Kenne noch nicht viele Befehle.)

kiri@kiri-GA-A75M-UD2H:/media/kiri/669906CF0ED66921/.Trash-1000/files/.Trash-999files/löschen$ rm -rf duplicity-full.20180528T165211Z.vol1529.difftar.gz
rm: das Entfernen von 'duplicity-full.20180528T165211Z.vol1529.difftar.gz' ist nicht möglich: Eingabe-/Ausgabefehler

Ich danke euch schon einmal für eine leicht verständliche Lösung!

seahawk1986

Anmeldungsdatum:
27. Oktober 2006

Beiträge: 11278

Bei einem Eingabe-/Ausgabefehler würde ich mir die Frage stellen, ob die externe Festplatte noch in Ordnung ist. In der Ausgabe von dmesg sollte man mehr zum Fehler sehen können und mit Festplattenstatus kannst du prüfen, ob die Platte offensichtliche Fehler meldet (falls der Controller S.M.A.R.T. unterstützt).

kirinoko

(Themenstarter)

Anmeldungsdatum:
15. September 2015

Beiträge: 187

Habe smartmontools installiert.

Der Suchlauf sollte vor einer Stunde fertig sein, jetzt habe ich ihn abgebrochen.

Er ergab:

iri@kiri-GA-A75M-UD2H:~$ sudo smartctl -x /dev/sdc #Status der ersten SATA-Platte ermitteln 
smartctl 6.6 2016-05-31 r4324 [x86_64-linux-4.13.0-43-generic] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Model Family:     Hitachi/HGST Travelstar Z7K500
Device Model:     HGST HTS725050A7E630
Serial Number:    RCF50ACE1HV54M
LU WWN Device Id: 5 000cca 85ed54b4b
Firmware Version: GS2OA340
User Capacity:    500.107.862.016 bytes [500 GB]
Sector Sizes:     512 bytes logical, 4096 bytes physical
Rotation Rate:    7200 rpm
Form Factor:      2.5 inches
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   ACS-2, ATA8-ACS T13/1699-D revision 6
SATA Version is:  SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is:    Fri Jun  8 13:49:59 2018 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is:   Unavailable
APM level is:     128 (minimum power consumption without standby)
Rd look-ahead is: Enabled
Write cache is:   Enabled
ATA Security is:  Disabled, NOT FROZEN [SEC1]
Wt Cache Reorder: Unknown

=== START OF READ SMART DATA SECTION ===
SMART Status not supported: Incomplete response, ATA output registers missing
SMART overall-health self-assessment test result: PASSED
Warning: This result is based on an Attribute check.

General SMART Values:
Offline data collection status:  (0x00)	Offline data collection activity
					was never started.
					Auto Offline Data Collection: Disabled.
Self-test execution status:      (   0)	The previous self-test routine completed
					without error or no self-test has ever 
					been run.
Total time to complete Offline 
data collection: 		(   45) seconds.
Offline data collection
capabilities: 			 (0x51) SMART execute Offline immediate.
					No Auto Offline data collection support.
					Suspend Offline collection upon new
					command.
					No Offline surface scan supported.
					Self-test supported.
					No Conveyance Self-test supported.
					Selective Self-test supported.
SMART capabilities:            (0x0003)	Saves SMART data before entering
					power-saving mode.
					Supports SMART auto save timer.
Error logging capability:        (0x01)	Error logging supported.
					General Purpose Logging supported.
Short self-test routine 
recommended polling time: 	 (   2) minutes.
Extended self-test routine
recommended polling time: 	 (  90) minutes.
SCT capabilities: 	       (0x003d)	SCT Status supported.
					SCT Error Recovery Control supported.
					SCT Feature Control supported.
					SCT Data Table supported.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAGS    VALUE WORST THRESH FAIL RAW_VALUE
  1 Raw_Read_Error_Rate     POSR-K   100   100   062    -    0
  2 Throughput_Performance  P-S--K   100   100   040    -    0
  3 Spin_Up_Time            PO---K   245   100   033    -    1
  4 Start_Stop_Count        -O--CK   100   100   000    -    566
  5 Reallocated_Sector_Ct   PO--CK   100   100   005    -    0
  7 Seek_Error_Rate         POSR-K   100   100   067    -    0
  8 Seek_Time_Performance   P-S--K   100   100   040    -    0
  9 Power_On_Hours          -O--CK   100   100   000    -    277
 10 Spin_Retry_Count        PO--CK   100   100   060    -    0
 12 Power_Cycle_Count       -O--CK   100   100   000    -    417
183 Runtime_Bad_Block       -O--CK   100   100   001    -    0
184 End-to-End_Error        PO--CK   100   100   097    -    0
187 Reported_Uncorrect      -O--CK   100   001   000    -    111
188 Command_Timeout         -O--CK   100   069   000    -    6970838286380
190 Airflow_Temperature_Cel -O---K   069   061   045    -    31 (Min/Max 21/39)
191 G-Sense_Error_Rate      -O--CK   100   100   000    -    5
192 Power-Off_Retract_Count -O--CK   100   100   000    -    3276850
193 Load_Cycle_Count        -O--CK   096   096   000    -    48158
196 Reallocated_Event_Count -O--CK   100   100   000    -    0
197 Current_Pending_Sector  -O--CK   100   100   000    -    0
198 Offline_Uncorrectable   ----CK   100   100   000    -    0
199 UDMA_CRC_Error_Count    -OS-CK   100   100   000    -    0
223 Load_Retry_Count        -O-R-K   100   100   000    -    0
                            ||||||_ K auto-keep
                            |||||__ C event count
                            ||||___ R error rate
                            |||____ S speed/performance
                            ||_____ O updated online
                            |______ P prefailure warning

General Purpose Log Directory Version 1
SMART           Log Directory Version 1 [multi-sector log support]
Address    Access  R/W   Size  Description
0x00       GPL,SL  R/O      1  Log Directory
0x01           SL  R/O      1  Summary SMART error log
0x02           SL  R/O      1  Comprehensive SMART error log
0x03       GPL     R/O      1  Ext. Comprehensive SMART error log
0x06           SL  R/O      1  SMART self-test log
0x07       GPL     R/O      1  Extended self-test log
0x09           SL  R/W      1  Selective self-test log
0x10       GPL     R/O      1  SATA NCQ Queued Error log
0x11       GPL     R/O      1  SATA Phy Event Counters log
0x80-0x9f  GPL,SL  R/W     16  Host vendor specific log
0xe0       GPL,SL  R/W      1  SCT Command/Status
0xe1       GPL,SL  R/W      1  SCT Data Transfer

SMART Extended Comprehensive Error Log Version: 1 (1 sectors)
Device Error Count: 111 (device log contains only the most recent 4 errors)
	CR     = Command Register
	FEATR  = Features Register
	COUNT  = Count (was: Sector Count) Register
	LBA_48 = Upper bytes of LBA High/Mid/Low Registers ]  ATA-8
	LH     = LBA High (was: Cylinder High) Register    ]   LBA
	LM     = LBA Mid (was: Cylinder Low) Register      ] Register
	LL     = LBA Low (was: Sector Number) Register     ]
	DV     = Device (was: Device/Head) Register
	DC     = Device Control Register
	ER     = Error register
	ST     = Status register
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 111 [2] occurred at disk power-on lifetime: 76 hours (3 days + 4 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  10 -- 41 01 70 00 00 11 fd 08 80 01 00  Error: IDNF at LBA = 0x11fd0880 = 301795456

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  61 04 00 00 08 00 00 11 fd 44 00 40 00     01:19:59.991  WRITE FPDMA QUEUED
  61 04 00 00 00 00 00 11 fd 40 00 40 00     01:19:59.991  WRITE FPDMA QUEUED
  61 04 00 00 58 00 00 11 fd 3c 00 40 00     01:19:59.990  WRITE FPDMA QUEUED
  61 04 00 00 50 00 00 11 fd 38 00 40 00     01:19:59.988  WRITE FPDMA QUEUED
  61 04 00 00 48 00 00 11 fd 34 00 40 00     01:19:59.985  WRITE FPDMA QUEUED

Error 110 [1] occurred at disk power-on lifetime: 76 hours (3 days + 4 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  10 -- 41 04 00 00 00 11 fb 08 00 01 00  Error: IDNF at LBA = 0x11fb0800 = 301664256

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  61 04 00 00 58 00 00 11 fc 78 00 40 00     01:19:28.827  WRITE FPDMA QUEUED
  61 04 00 00 50 00 00 11 fc 74 00 40 00     01:19:28.826  WRITE FPDMA QUEUED
  61 04 00 00 48 00 00 11 fc 70 00 40 00     01:19:28.824  WRITE FPDMA QUEUED
  61 04 00 00 40 00 00 11 fc 6c 00 40 00     01:19:28.823  WRITE FPDMA QUEUED
  61 04 00 00 38 00 00 11 fc 68 00 40 00     01:19:28.822  WRITE FPDMA QUEUED

Error 109 [0] occurred at disk power-on lifetime: 76 hours (3 days + 4 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  10 -- 41 03 90 00 00 11 fb 90 70 01 00  Error: IDNF at LBA = 0x11fb9070 = 301699184

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  61 04 00 00 40 00 00 11 fb bc 00 40 00     01:18:57.853  WRITE FPDMA QUEUED
  61 04 00 00 38 00 00 11 fb b8 00 40 00     01:18:57.850  WRITE FPDMA QUEUED
  61 04 00 00 30 00 00 11 fb b4 00 40 00     01:18:57.845  WRITE FPDMA QUEUED
  61 04 00 00 28 00 00 11 fb b0 00 40 00     01:18:57.839  WRITE FPDMA QUEUED
  61 04 00 00 20 00 00 11 fb ac 00 40 00     01:18:57.838  WRITE FPDMA QUEUED

Error 108 [3] occurred at disk power-on lifetime: 76 hours (3 days + 4 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  10 -- 41 04 00 00 00 11 f9 58 00 01 00  Error: IDNF at LBA = 0x11f95800 = 301553664

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  61 04 00 00 10 00 00 11 f9 90 00 40 00     01:18:26.768  WRITE FPDMA QUEUED
  61 04 00 00 08 00 00 11 f9 8c 00 40 00     01:18:26.764  WRITE FPDMA QUEUED
  61 04 00 00 00 00 00 11 f9 88 00 40 00     01:18:26.764  WRITE FPDMA QUEUED
  61 04 00 00 58 00 00 11 f9 84 00 40 00     01:18:26.763  WRITE FPDMA QUEUED
  61 04 00 00 50 00 00 11 f9 80 00 40 00     01:18:26.761  WRITE FPDMA QUEUED

SMART Extended Self-test Log Version: 1 (1 sectors)
Num  Test_Description    Status                  Remaining  LifeTime(hours)  LBA_of_first_error
# 1  Extended offline    Completed without error       00%       276         -
# 2  Short offline       Completed without error       00%        13         -

SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

SCT Status Version:                  3
SCT Version (vendor specific):       256 (0x0100)
SCT Support Level:                   1
Device State:                        Active (0)
Current Temperature:                    31 Celsius
Power Cycle Min/Max Temperature:     21/39 Celsius
Lifetime    Min/Max Temperature:     13/39 Celsius
Lifetime    Average Temperature:        27 Celsius
Under/Over Temperature Limit Count:   0/0

SCT Temperature History Version:     2
Temperature Sampling Period:         1 minute
Temperature Logging Interval:        1 minute
Min/Max recommended Temperature:      0/60 Celsius
Min/Max Temperature Limit:           -40/65 Celsius
Temperature History Size (Index):    128 (38)

Index    Estimated Time   Temperature Celsius
  39    2018-06-08 11:43    39  ********************
 ...    ..( 58 skipped).    ..  ********************
  98    2018-06-08 12:42    39  ********************
  99    2018-06-08 12:43    38  *******************
 100    2018-06-08 12:44    37  ******************
 101    2018-06-08 12:45    37  ******************
 102    2018-06-08 12:46    36  *****************
 103    2018-06-08 12:47    35  ****************
 104    2018-06-08 12:48    35  ****************
 105    2018-06-08 12:49    34  ***************
 106    2018-06-08 12:50    34  ***************
 107    2018-06-08 12:51    33  **************
 ...    ..(  2 skipped).    ..  **************
 110    2018-06-08 12:54    33  **************
 111    2018-06-08 12:55    32  *************
 ...    ..(  5 skipped).    ..  *************
 117    2018-06-08 13:01    32  *************
 118    2018-06-08 13:02    31  ************
 ...    ..( 47 skipped).    ..  ************
  38    2018-06-08 13:50    31  ************

SMART WRITE LOG does not return COUNT and LBA_LOW register
SCT (Get) Error Recovery Control command failed

Device Statistics (GP/SMART Log 0x04) not supported

SATA Phy Event Counters (GP Log 0x11)
ID      Size     Value  Description
0x0001  2            0  Command failed due to ICRC error
0x0002  2            0  R_ERR response for data FIS
0x0003  2            0  R_ERR response for device-to-host data FIS
0x0004  2            0  R_ERR response for host-to-device data FIS
0x0005  2            0  R_ERR response for non-data FIS
0x0006  2            0  R_ERR response for device-to-host non-data FIS
0x0007  2            0  R_ERR response for host-to-device non-data FIS
0x0009  2            1  Transition from drive PhyRdy to drive PhyNRdy
0x000a  2            0  Device-to-host register FISes sent due to a COMRESET
0x000b  2            0  CRC errors within host-to-device FIS
0x000d  2            0  Non-CRC errors within host-to-device FIS

Ist trotz des Abbruchs eine Interpretation zum Zustand der externen Festplatte möglich? sdc ist die ex. Festplatte!

seahawk1986

Anmeldungsdatum:
27. Oktober 2006

Beiträge: 11278

Wie ist die Platte denn angeschlossen (ggf. mal ein anderes Kabel nehmen)? Hat die externe Platte ein eigenes Netzteil? Hängt sie an einem passiven Hub? Was steht in der Ausgabe von dmesg?

Antworten |