staging.inyokaproject.org

Ach, und vielen Dank für deine extreme Hilfe!! ☺

Bei dir schein einiges im Argen.Zeige

systemctl status systemd-modules-load.service

cat /etc/sane.d/pixma.conf

cat /etc/services | grep sane

sudo sane-find-scanner

Korrigiere deine Rechte im Home

sudo chown -R -v $USER:$USER $HOME

Füge dich zur Gruppe Scanner dazu

sudo adduser $USER scanner

Neustart und wieder Testen.

Hi, ich kann jetzt erst ab Mitte Mai antworten, da ich jetzt in Urlaub bin. Sobald ich wieder da bin poste ich die Ausgaben. Danke dir ertmal!!

Alles klar 😉 Schönen Urlaub wünsche ich 👍

So, ich bin wieder da...! 😉

systemctl status systemd-modules-load.service

● systemd-modules-load.service - Load Kernel Modules
   Loaded: loaded (/lib/systemd/system/systemd-modules-load.service; static; vendor preset: enabled)
   Active: failed (Result: exit-code) since Fri 2018-05-18 19:31:10 CEST; 7min ago
     Docs: man:systemd-modules-load.service(8)
           man:modules-load.d(5)
  Process: 578 ExecStart=/lib/systemd/systemd-modules-load (code=exited, status=1/FAILURE)
 Main PID: 578 (code=exited, status=1/FAILURE)
                                                                                                                                               
Mai 18 19:31:10 acer systemd[1]: Starting Load Kernel Modules...                                                                               
Mai 18 19:31:10 acer systemd-modules-load[578]: Failed to find module 'snd_bt_sco'                                                             
Mai 18 19:31:10 acer systemd[1]: systemd-modules-load.service: Main process exited, code=exited, status=1/FAILURE                              
Mai 18 19:31:10 acer systemd[1]: systemd-modules-load.service: Failed with result 'exit-code'.
Mai 18 19:31:10 acer systemd[1]: Failed to start Load Kernel Modules.

cat /etc/sane.d/pixma.conf

# pixma.conf configuration for the sane pixma backend
#
# bjnp-timeout=5000
# Specify the timeout (in ms) to be used for all the folllowing
# scanners.
# May be specified multiple times.
# The last value (if any) will be used for auto-detection
#
# define URI's of scanners (one per line)
# This is only used for network scanners.
# normally scanners will be detected by sending a broadcast
# if this does not work under your OS, or if the scanners
# are on a different subnet, configure your scanners URI here
#
# method must be bjnp
# port number can normally be left out, port 8612 is used as default
# The timeout parameter sets a timeout value for the scanner on
# the same line
# Example:
# bjnp://myscanner.my.domain:8612 // uses the default 1000ms timeout
# bjnp-timeout=5000
# bjnp://printer-1.pheasant.org // will use the 5000 ms timeout
# bjnp://scanner.bad-network.org/timeout=1500 // timeout set to 1500 ms
# bjnp-timeout=3000 // will be used for auto-detected scanners
#

cat /etc/services | grep sane

sane-port       6566/tcp        sane saned      # SANE network scanner daemon

sudo sane-find-scanner

# sane-find-scanner will now attempt to detect your scanner. If the
  # result is different from what you expected, first make sure your
  # scanner is powered up and properly connected to your computer.

  # No SCSI scanners found. If you expected something different, make sure that
  # you have loaded a kernel SCSI driver for your SCSI adapter.

found USB scanner (vendor=0x0bda [Generic], product=0x0129 [USB2.0-CRW]) at libusb:002:004
  # Your USB scanner was (probably) detected. It may or may not be supported by
  # SANE. Try scanimage -L and read the backend's manpage.

  # Not checking for parallel port scanners.

  # Most Scanners connected to the parallel port or other proprietary ports
  # can't be detected by this program.

Dem Rest habe ich ausgeführt, aber leider ohne Erfolg! ;(

Übrigens, wenn ich gscan2pdf als sudo kommt das:

gscan2pdf:4628): Gtk-WARNING **: 19:43:28.092: Theme parsing error: gtk.css:68:35: The style property GtkButton:child-displacement-x is deprecated and shouldn't be used anymore. It will be removed in a future version

(gscan2pdf:4628): Gtk-WARNING **: 19:43:28.093: Theme parsing error: gtk.css:69:35: The style property GtkButton:child-displacement-y is deprecated and shouldn't be used anymore. It will be removed in a future version

(gscan2pdf:4628): Gtk-WARNING **: 19:43:28.093: Theme parsing error: gtk.css:70:34: The style property GtkCheckButton:indicator-size is deprecated and shouldn't be used anymore. It will be removed in a future version

(gscan2pdf:4628): Gtk-WARNING **: 19:43:28.093: Theme parsing error: gtk.css:71:36: The style property GtkCheckMenuItem:indicator-size is deprecated and shouldn't be used anymore. It will be removed in a future version

(gscan2pdf:4628): Gtk-WARNING **: 19:43:28.093: Theme parsing error: gtk.css:73:46: The style property GtkScrolledWindow:scrollbars-within-bevel is deprecated and shouldn't be used anymore. It will be removed in a future version

(gscan2pdf:4628): Gtk-WARNING **: 19:43:28.094: Theme parsing error: gtk.css:76:30: The style property GtkExpander:expander-size is deprecated and shouldn't be used anymore. It will be removed in a future version

(gscan2pdf:4628): Gtk-WARNING **: 19:43:28.095: Theme parsing error: gtk.css:83:29: The style property GtkStatusbar:shadow-type is deprecated and shouldn't be used anymore. It will be removed in a future version

Vielleicht hilft dir das ja weiter....

Hoffe du hast dich gut Erholt ☺

Zeige mal

sudo systemctl start systemd-modules-load.service

journalctl -xe

Wieso taucht der Scanner bei

sudo sane-find-scanner

nicht auf? War er defensiv eingeschaltet/Angeschlossen? Nochmal

export SANE_DEBUG_BJNP="5" && scanimage -L

zeigen.

Ja, es war zwar anstrengend, aber ich bi extrem gut erholt! 😉

sudo systemctl start systemd-modules-load.service

ob for systemd-modules-load.service failed because the control process exited with error code.
See "systemctl status systemd-modules-load.service" and "journalctl -xe" for details.

journalctl -xe

Mai 20 11:20:45 acer org.kde.ActivityManager[2104]: Creating the cache for:  "applications:org.kde.konsole.desktop"
Mai 20 11:20:45 acer org.kde.ActivityManager[2104]: Already in database?  true
Mai 20 11:20:45 acer org.kde.ActivityManager[2104]:       First update :  QDateTime(2018-01-28 20:16:24.000 CET Qt::TimeSpec(LocalTime))
Mai 20 11:20:45 acer org.kde.ActivityManager[2104]:        Last update :  QDateTime(2018-05-19 09:45:26.000 CEST Qt::TimeSpec(LocalTime))
Mai 20 11:20:45 acer org.kde.ActivityManager[2104]: After the adjustment
Mai 20 11:20:45 acer org.kde.ActivityManager[2104]:      Current score :  22.4248
Mai 20 11:20:45 acer org.kde.ActivityManager[2104]:       First update :  QDateTime(2018-01-28 20:16:24.000 CET Qt::TimeSpec(LocalTime))
Mai 20 11:20:45 acer org.kde.ActivityManager[2104]:        Last update :  QDateTime(2018-05-19 09:45:26.000 CEST Qt::TimeSpec(LocalTime))
Mai 20 11:20:45 acer org.kde.ActivityManager[2104]: Interval length is  0
Mai 20 11:20:45 acer org.kde.ActivityManager[2104]:          New score :  23.4248
Mai 20 11:20:45 acer org.kde.ActivityManager[2104]: ResourceScoreUpdated: "85d3007b-091c-4044-905c-7415784524bc" "org.kde.libtaskmanager" "appl
Mai 20 11:21:01 acer sudo[3913]:      ivt : TTY=pts/1 ; PWD=/home/ivt ; USER=root ; COMMAND=/bin/systemctl start systemd-modules-load.service
Mai 20 11:21:01 acer sudo[3913]: pam_unix(sudo:session): session opened for user root by ivt(uid=0)
Mai 20 11:21:01 acer systemd[1]: Starting Load Kernel Modules...
-- Subject: Unit systemd-modules-load.service has begun start-up
-- Defined-By: systemd
-- Support: http://www.ubuntu.com/support
-- 
-- Unit systemd-modules-load.service has begun starting up.
Mai 20 11:21:01 acer systemd-modules-load[3917]: Failed to find module 'snd_bt_sco'
Mai 20 11:21:01 acer systemd[1]: systemd-modules-load.service: Main process exited, code=exited, status=1/FAILURE
Mai 20 11:21:01 acer systemd[1]: systemd-modules-load.service: Failed with result 'exit-code'.
Mai 20 11:21:01 acer systemd[1]: Failed to start Load Kernel Modules.
-- Subject: Unit systemd-modules-load.service has failed
-- Defined-By: systemd
-- Support: http://www.ubuntu.com/support
-- 
-- Unit systemd-modules-load.service has failed.
-- 
-- The result is RESULT.
Mai 20 11:21:01 acer sudo[3913]: pam_unix(sudo:session): session closed for user root
Mai 20 11:21:10 acer dbus-daemon[2104]: [session uid=1000 pid=2104] Failed to activate service 'org.freedesktop.Telepathy.Client.KTp.KdedIntegr
Mai 20 11:21:55 acer wpa_supplicant[777]: wlp2s0: WPA: Group rekeying completed with 38:10:d5:3d:24:29 [GTK=TKIP]
Mai 20 11:22:14 acer dbus-daemon[748]: [system] Activating service name='org.debian.AptXapianIndex' requested by ':1.34' (uid=1000 pid=2740 com
Mai 20 11:22:14 acer dbus-daemon[748]: [system] Successfully activated service 'org.debian.AptXapianIndex'
Mai 20 11:22:14 acer dbus-daemon[748]: [system] Rejected send message, 0 matched rules; type="method_return", sender=":1.65" (uid=0 pid=4001 co

sudo sane-find-scanner (ich bilde mir ein, das er an war. Jetzt ist er definitiv an.)

  # sane-find-scanner will now attempt to detect your scanner. If the
  # result is different from what you expected, first make sure your
  # scanner is powered up and properly connected to your computer.

  # No SCSI scanners found. If you expected something different, make sure that
  # you have loaded a kernel SCSI driver for your SCSI adapter.

found USB scanner (vendor=0x0bda [Generic], product=0x0129 [USB2.0-CRW]) at libusb:002:004
  # Your USB scanner was (probably) detected. It may or may not be supported by
  # SANE. Try scanimage -L and read the backend's manpage.

  # Not checking for parallel port scanners.

  # Most Scanners connected to the parallel port or other proprietary ports
  # can't be detected by this program.

export SANE_DEBUG_BJNP="5" && scanimage -L

[sanei_debug] Setting debug level of bjnp to 5.
[bjnp] sanei_bjnp_find_devices, pixma backend version: 0.17.46
[bjnp] sanei_bjnp_find_devices: No devices specified in configuration file.
[bjnp] sanei_bjnp_find_devices: Added all configured scanners, now do auto detection...
[bjnp] prepare_socket: lo is not a valid IPv4 interface, skipping...
[bjnp] prepare_socket: wlp2s0 is IPv4 capable, sending broadcast, socket = 42
[bjnp] prepare_socket: lo is not a valid IPv6 interface, skipping...
[bjnp] prepare_socket: wlp2s0 is IPv6 capable, sending broadcast, socket = 43
[bjnp] prepare_socket: wlp2s0 is IPv6 capable, sending broadcast, socket = 45
[bjnp] prepare_socket: wlp2s0 is IPv6 capable, sending broadcast, socket = 46
[bjnp] sanei_bjnp_find_devices: Select returned, time left 0.441908....
[bjnp] sanei_find_devices: Discover response:
[bjnp]  00000000:42 4a 4e 50 82 01 00 00  00 00 00 00 00 00 00 10 
[bjnp]  00000010:00 01 08 00 06 04 f8 0d  60 52 74 c5 c0 a8 02 0a 
[bjnp] get_scanner_name: Forward lookup for 5274C5000000.fritz.box succeeded, using as hostname
[bjnp] bjnp_allocate_device(bjnp://5274C5000000.fritz.box:8612/timeout=1000) 0
[bjnp] get_scanner_name: Forward lookup for CanonMX925.fritz.box succeeded, using as hostname
[bjnp] setup_udp_socket: Setting up a UDP socket, dest: 192.168.2.10  port 8612
[bjnp] bjnp_get_scanner_mac_address: Discover response:
[bjnp]  00000000:42 4a 4e 50 82 01 00 00  00 00 00 00 00 00 00 10 
[bjnp]  00000010:00 01 08 00 06 04 f8 0d  60 52 74 c5 c0 a8 02 0a 
[bjnp] bjnp_allocate_device: Scanner not yet in our list, added it: 5274C5000000.fritz.box:8612
[bjnp] get_scanner_id: Get scanner identity
[bjnp]  00000000:42 4a 4e 50 02 30 00 00  00 01 00 00 00 00 00 00 
[bjnp] setup_udp_socket: Setting up a UDP socket, dest: 192.168.2.10  port 8612
[bjnp] get_scanner_id: scanner identity:
[bjnp]  00000000:42 4a 4e 50 82 30 00 00  00 01 00 00 00 00 00 65 
[bjnp]  00000010:00 65 4d 46 47 3a 43 61  6e 6f 6e 3b 43 4d 44 3a 
[bjnp]  00000020:4d 75 6c 74 69 50 61 73  73 20 32 2e 31 2c 49 56 
[bjnp]  00000030:45 43 3b 4d 44 4c 3a 4d  58 39 32 30 20 73 65 72 
[bjnp]  00000040:69 65 73 3b 43 4c 53 3a  49 4d 41 47 45 3b 44 45 
[bjnp]  00000050:53 3a 43 61 6e 6f 6e 20  4d 58 39 32 30 20 73 65 
[bjnp]  00000060:72 69 65 73 3b 53 4f 4a  3a 42 4a 4e 50 32 2c 42 
[bjnp]  00000070:4a 4e 50 65 3b 
[bjnp] get_scanner_id: Scanner identity string = MFG:Canon;CMD:MultiPass 2.1,IVEC;MDL:MX920 series;CLS:IMAGE;DES:Canon MX920 series;SOJ:BJNP2,BJNPe; - length = 99
[bjnp] get_scanner_id: Scanner model = MX920 series
[bjnp] add_scanner: New scanner added: bjnp://5274C5000000.fritz.box:8612/timeout=1000, serial 5274C5000000, mac address: f80d605274c5.
[bjnp] sanei_bjnp_find_devices: Select returned, time left 0.499993....
[bjnp] sanei_find_devices: Discover response:
[bjnp]  00000000:42 4a 4e 50 82 01 00 00  00 00 00 00 00 00 00 10 
[bjnp]  00000010:00 01 08 00 06 04 f8 0d  60 52 74 c5 c0 a8 02 0a 
[bjnp] get_scanner_name: Forward lookup for CanonMX925.fritz.box succeeded, using as hostname
[bjnp] bjnp_allocate_device(bjnp://CanonMX925.fritz.box:8612/timeout=1000) 1
[bjnp] get_scanner_name: Forward lookup for CanonMX925.fritz.box succeeded, using as hostname
[bjnp] setup_udp_socket: Setting up a UDP socket, dest: 192.168.2.10  port 8612
[bjnp] bjnp_get_scanner_mac_address: Discover response:
[bjnp]  00000000:42 4a 4e 50 82 01 00 00  00 00 00 00 00 00 00 10 
[bjnp]  00000010:00 01 08 00 06 04 f8 0d  60 52 74 c5 c0 a8 02 0a 
[bjnp] add_scanner: Scanner at bjnp://CanonMX925.fritz.box:8612/timeout=1000 was added before, good!
[bjnp] sanei_find_devices: scanner discovery finished...
device `pixma:MX920_5274C5000000' is a CANON Canon PIXMA MX920 Series multi-function peripheral

Lass uns mal was Probieren. Datei erstellen

sudo nano /etc/udev/rules.d/79-udev-canon.rules

folgenden Inhalt einfügen

SYSFS{idVendor}=="04a9", SYSFS{idProduct}=="*", MODE="0777"

Speichern.

Folgende Datei anpassen

sudo nano /etc/sane.d/pixma.conf

dort den Eintrag ändern von

# bjnp-timeout=5000
in 
bjnp-timeout=5000
bjnp://192.168.2.10:8612

zeige noch

grep pixma /etc/sane.d/dll.conf

Neustart

Kellerkind, du bist mein Held! Ich möchte dich heiraten!. Er scannt einwandfrei. Vielen, vielen Dank für deine Hilfe.

Bin schon Verheiratet 😈 Freut mich aber sehr das es jetzt läuft! 👍

Ich bin ja dann doch immer begeistert, und verblüfft, wie gut man sich auskennen kann! 👍